помогите со step 7

Промышленные Логические Контроллеры SIMATIC S7-200/300/400
Post Reply
ROGNAROG
Posts: 74
Joined: Thu Oct 10, 2013 10:09 am

blocks OB1 , FB1 ,DB1 step 7

Post by ROGNAROG » Mon Feb 16, 2015 2:54 pm

создал блоки OB1 , FB1 ,DB1 step 7
в блоке FB1 прописал алгоритм запуска двигателя, создал блок данных,
открыл блок OB1 прописал все переменные( побывал именами и адресами)
открыл программу в симуляторе переменные не принимают значения,
если эти же алгоритмы прописать в OB1 то все работает замечательно,переписывал программу 3 раза все равно тоже самое,может кто не будь подскажет новичку в чем может быть причина???
created blocks OB1 , FB1 ,DB1 step 7
in block FB1 prescribed algorithm engine start, created a data block,
opened the block OB1 ordered all variables( visited names and addresses)
opened the program in the simulator variables take values
if these same algorithms to prescribe in OB1 everything works fine,rewrote the program 3 times still the same can anyone not be prompt to the beginner what could be the reason???

almaz78
Posts: 108
Joined: Tue Dec 16, 2008 7:36 pm

Re: blocks OB1 , FB1 ,DB1 step 7

Post by almaz78 » Mon Feb 16, 2015 3:44 pm

call FB1 from OB1

ROGNAROG
Posts: 74
Joined: Thu Oct 10, 2013 10:09 am

Re: blocks OB1 , FB1 ,DB1 step 7

Post by ROGNAROG » Tue Feb 17, 2015 7:15 am

almaz78 wrote:call FB1 from OB1
do but still does not work q... put in 1 and immediately resets itself

ROGNAROG
Posts: 74
Joined: Thu Oct 10, 2013 10:09 am

помогите со step 7

Post by ROGNAROG » Wed Feb 18, 2015 8:19 am

Привет всем.очень нуждаюсь в консультациях с программистом который работает со STEP7,книжек начитался но все равно не могу понять.может есть добрый человек который объяснит мне что и как нужно делать,чувствую сам я не справлюсь (h) (h) (h)

Ber56
Posts: 20
Joined: Fri Feb 18, 2011 12:43 pm

Re: помогите со step 7

Post by Ber56 » Wed Feb 18, 2015 11:18 am

Не специалист, но помогу чем могу обращайтесь.
Со STEP'ом работаю каждый день, так что предмет чуть более чем немного изучен.
ПОЧТЫ: uzbatsu@gmail.com
С жутко непонятными вещами, могу помочь по любому VNC.

Schtiel
Site Admin
Posts: 1121
Joined: Wed Sep 06, 2006 12:03 pm
Location: CIS

Re: blocks OB1 , FB1 ,DB1 step 7

Post by Schtiel » Wed Feb 18, 2015 4:27 pm

Post screenshots of FB1 / OB1

Oll Bell
Posts: 118
Joined: Sun Apr 17, 2011 9:49 pm

Re: помогите со step 7

Post by Oll Bell » Wed Feb 18, 2015 8:40 pm

Ber56 wrote:Не специалист, но помогу чем могу обращайтесь.
Со STEP'ом работаю каждый день, так что предмет чуть более чем немного изучен.
ПОЧТЫ: uzbatsu@gmail.com
С жутко непонятными вещами, могу помочь по любому VNC.
разрешите и мне вопросы спрашивать.

ROGNAROG
Posts: 74
Joined: Thu Oct 10, 2013 10:09 am

Re: blocks OB1 , FB1 ,DB1 step 7

Post by ROGNAROG » Thu Feb 19, 2015 9:11 am

Schtiel wrote:Post screenshots of FB1 / OB1
all I sort of understand,the reason was that the output signal is assigned to another variable,but now there's another question,I need envy variable which must be switched on and off with the Scud missiles but not left on the channel module type must be BOOL

Post Reply