Page 1 of 1

[LINK]: Omron password tool Xtal

Posted: Sat Jun 23, 2007 7:05 am
by mienha
Before I have Xtal software to unprotect PLC omron but my PC broken and I lost this software,
Who have this soft can post for me? thank you very much!

Posted: Sun Jun 24, 2007 2:46 pm
by most

Posted: Thu Nov 15, 2007 5:12 pm
by Олег
in Russian forum wrote:Можно без проблем снять пароль в контроллерах CS1, CJ1 до версии 2.0 в вериях от 2.0 и выше, как повезёт, зависит от того, с какими опциями установили пароль на программу. описание на http://cpu13.ru/forum/viewtopic.php?t=4
you can view passwords in "*.OBJ"
Image

Find OBJ file

Posted: Mon Jun 30, 2008 2:40 am
by Husanto
chongky wrote:what is *.obj file ?
where does it located ?
You can find the *.OBJ file in CF card after u back up PLC program. So, You must back up the PLC program first using CF card and you will find the obj file in there and you open it using Ultraedit or Winhex.

PLC write protected

Posted: Tue Jul 08, 2008 9:18 am
by amir1234
I have a CJ1 cpu that is protected. It is Overwrite protected, and It is prohibited from saving into a memory card.

1- How can I unlock it?
or at least how can clean it over write protection? so it be programmable again?

Posted: Tue Jul 08, 2008 1:03 pm
by Олег
Create the program without the Password
To keep on a memory card of as a file AUTOEXEC.OBJ and AUTOEXEC.STD
Push ON and to load the controller from a memory card
The old program will be erased
in Russian wrote:элементарно, сделать программу без пароля,
сохранить на карту как AUTOEXEC.OBJ и файл настроек AUTOEXEC.STD
и загрузить контроллер с карты при включении питания.
Старая программа в контроллере будет потеряна.

Unlock Protected CJ1

Posted: Sat Jul 12, 2008 2:24 pm
by Husanto
If i have one CPU CJ1M with password protected and protected copy to memory card.
Is possible to upload program from that PLC??
OR any idea to unlock the password protected??

Unlock password

Posted: Wed Jul 23, 2008 1:32 pm
by Husanto
The software can unlock password CJ series??

Posted: Sun Aug 03, 2008 3:29 pm
by chongky
huyviet,

I download the file already, but there is no .exe file, so how to use it ?

Posted: Mon Aug 04, 2008 11:32 am
by vlad2006gr
This is source code spain version. I have compiled and have translated on English, but did not check.
Link_is_Dead :(/Password_eng.exe
Write about results.
Good luck!

CQM1-H

Posted: Tue Aug 05, 2008 5:39 am
by vlad2006gr
CQM1-H blocks search of a code. To open the password it is impossible.

Omron CJ1

Posted: Tue Nov 25, 2008 2:59 pm
by ElBedos
Hi to all...
I try the program XTAL (version 1.00.0005) for my PLC Omron CJ1 but the program don't work (finish the scan to FFFF and write KEY NOT FOUND...). :(
Some know why? Or other program that work with this PLC???
Please, please, please... help me... :cry:
Very thanks...
:P

Re: [LINK]: Omron password tool Xtal

Posted: Fri Jan 18, 2013 3:13 pm
by ZENDER1
try Password (eng) - для CQM1 URL: http://z-forever.com/w/doku.php/soft:om ... nlock:list

Re: [LINK]: Omron password tool Xtal

Posted: Wed Apr 10, 2013 3:09 pm
by hmohamed
hi zender

the link you send is not working please upload again (wow)

Re:

Posted: Mon Jul 21, 2014 11:32 am
by letranlong
Олег wrote:Create the program without the Password
To keep on a memory card of as a file AUTOEXEC.OBJ and AUTOEXEC.STD
Push ON and to load the controller from a memory card
The old program will be erased
in Russian wrote:элементарно, сделать программу без пароля,
сохранить на карту как AUTOEXEC.OBJ и файл настроек AUTOEXEC.STD
и загрузить контроллер с карты при включении питания.
Старая программа в контроллере будет потеряна.
please hepl me upload plc omron CPM1A
I have a question for everyone
i hepl everyone help me
i have a types plc omron CPM1A and CPM2A, i when upload programs data all in plc but me upload being error
i have a question for your help, i have found errors when i upload plc omron CPM1A and CPM2A but programs plc being unlock password . those errors are shown that i send attach image.
could you help
please. for me a software to fix opening password plc omron.
what is software opening password plc omron CPM1a and CPM2A?
please. can you give me a link ? I to fix open password plc omron
thank you so much for your time and consideration.
https://goo.gl/MymW6Q

Re: Re:

Posted: Tue Jul 22, 2014 8:36 am
by hmohamed
letranlong wrote:
Олег wrote:Create the program without the Password
To keep on a memory card of as a file AUTOEXEC.OBJ and AUTOEXEC.STD
Push ON and to load the controller from a memory card
The old program will be erased
in Russian wrote:элементарно, сделать программу без пароля,
сохранить на карту как AUTOEXEC.OBJ и файл настроек AUTOEXEC.STD
и загрузить контроллер с карты при включении питания.
Старая программа в контроллере будет потеряна.
please hepl me upload plc omron CPM1A
I have a question for everyone
i hepl everyone help me
i have a types plc omron CPM1A and CPM2A, i when upload programs data all in plc but me upload being error
i have a question for your help, i have found errors when i upload plc omron CPM1A and CPM2A but programs plc being unlock password . those errors are shown that i send attach image.
could you help
please. for me a software to fix opening password plc omron.
what is software opening password plc omron CPM1a and CPM2A?
please. can you give me a link ? I to fix open password plc omron
thank you so much for your time and consideration.


Go to this site and you will find what you need
http://www.plcjiemi.com/

Re: Re:

Posted: Tue Jul 22, 2014 8:38 am
by hmohamed
letranlong wrote:
Олег wrote:Create the program without the Password
To keep on a memory card of as a file AUTOEXEC.OBJ and AUTOEXEC.STD
Push ON and to load the controller from a memory card
The old program will be erased
in Russian wrote:элементарно, сделать программу без пароля,
сохранить на карту как AUTOEXEC.OBJ и файл настроек AUTOEXEC.STD
и загрузить контроллер с карты при включении питания.
Старая программа в контроллере будет потеряна.
please hepl me upload plc omron CPM1A
I have a question for everyone
i hepl everyone help me
i have a types plc omron CPM1A and CPM2A, i when upload programs data all in plc but me upload being error
i have a question for your help, i have found errors when i upload plc omron CPM1A and CPM2A but programs plc being unlock password . those errors are shown that i send attach image.
could you help
please. for me a software to fix opening password plc omron.
what is software opening password plc omron CPM1a and CPM2A?
please. can you give me a link ? I to fix open password plc omron
thank you so much for your time and consideration.


Go to this site and you will find what you need
http://www.plcjiemi.com/ or http://www.ymmfa.com/thread-gkfid-37.html

Good Luck

Re: Re:

Posted: Sat Aug 02, 2014 4:32 pm
by letranlong
hmohamed wrote:
letranlong wrote:
Олег wrote:Create the program without the Password
To keep on a memory card of as a file AUTOEXEC.OBJ and AUTOEXEC.STD
Push ON and to load the controller from a memory card
The old program will be erased
in Russian wrote:элементарно, сделать программу без пароля,
сохранить на карту как AUTOEXEC.OBJ и файл настроек AUTOEXEC.STD
и загрузить контроллер с карты при включении питания.
Старая программа в контроллере будет потеряна.
please hepl me upload plc omron CPM1A
I have a question for everyone
i hepl everyone help me
i have a types plc omron CPM1A and CPM2A, i when upload programs data all in plc but me upload being error
i have a question for your help, i have found errors when i upload plc omron CPM1A and CPM2A but programs plc being unlock password . those errors are shown that i send attach image.
could you help
please. for me a software to fix opening password plc omron.
what is software opening password plc omron CPM1a and CPM2A?
please. can you give me a link ? I to fix open password plc omron
thank you so much for your time and consideration.


Go to this site and you will find what you need
http://www.plcjiemi.com/ or http://www.ymmfa.com/thread-gkfid-37.html

Good Luck
thank you very much
dear everybody
please you help me
I when unlock pass plc onrom CPM1A by software XTAL
but I unlock password plc omron CPM1A being errors, i have sent image attach.
there are some steps that , I have made/ done below;
the first time I connect cable RS232 go to PC with plc, after I opening software CX one 9.0
I'm online with plc but plc, has lock password so I can't upload
after I opening software unlock password plc onrom CPM1A by software Xtal but I when unlock password this time software Xtal being errors
i don't know, what is this errors ?
how can I modify error '8005' ?
what is this error run-time error '8005': ?

https://www.youtube.com/watch?v=v4J4SAZGMNA