Page 1 of 1

[? RUS]: Can't connecting to MAGELIS XBT-P022010 panel

Posted: Thu Dec 11, 2008 7:06 am
by Alexsander
Can't connecting to MAGELIS XBT-P022010 panel
I have soft XBT-L1000 V4.42
cabel XBTZ915 9 pins: 2-2, 3-3, 7-5, and short 7-8,6-4
Russian wrote:Не могу соедениться с панелью MAGELIS XBT-P022010
Люди добрые помогите с советом.
Суть вопроса такова - есть софт XBT-L1000 V4.42,
есть панель оаператора MAGELIS XBT-P022010.
Распайку соеденительного кабеля выполнил в соответствии со схемой XBTZ915 2-2, 3-3,7-5 на 9 пиновом(СОМ порт) перемычки 7-8,6-4.
Хочу соеденится с панелью и открыть проект.
В XBT-L1000 выбираю TRANSFERS-IMPORT-FROM TERMINAL и выскакивает фатальность соединения.
При этом проверяю Drivers Manager соединение, все окей.
В чем дело не пойму.

Posted: Sun May 03, 2009 8:23 am
by curbat
Столкнулся с такой же проблемой. Интересно удалось ли автору решить её. Может нужно что то нажать на панели, чтобы она стала готова для transfer? Как на сименовских, омроновских панелях. Кто знает подскажите пожалуйста.
Has faced the same problem. Whether interestingly it was possible to the author to solve it. That can is necessary that to press panels that it became ready for transfer? As on Siemens and Omron panels. Who knows prompt please.

XBTL1000 Problem

Posted: Tue May 05, 2009 1:39 pm
by leofarhan
Which error message you are getting.

Please check the link below, this might help you.

If you are facing error "This is not an XBTL1000 file"

http://www.download.schneider-electric. ... ument&L=EN

Posted: Wed May 06, 2009 4:28 am
by curbat
My software ist German. First that that "check connecting to terminal" "Ueberpruefung des angeschlossenen Terminals..". Next error ist "kein terminal angeschlossen". That that "not connecting to terminal"

Posted: Tue May 12, 2009 12:30 pm
by Alexsander
thank leofarhan
But when download v4.5 ?
Спасибо leofarhan.
Замена файла применимо к версии 4.5 и выше.
Теперь вопрос где взять версию 4.5?

XBT-L1000 4.51 Pro

Posted: Wed May 13, 2009 8:41 pm
by vlad2006gr
XBT-L1000 4.51 Pro
Link_is_Dead :(/Doc.rar
Link_is_Dead :(/X ... .part1.rar
Link_is_Dead :(/X ... .part2.rar

Alexsander перемычка 8-13 со стороны маджелиса есть?
Drivers Manager не надо использовать- параметры связи устанавливаются в XBT-L1000. Driver pack установи версии выше 1.7, ком порт 1.

Posted: Wed May 20, 2009 10:08 am
by Alexsander
Спасибо Владимир (vlad2006gr) за неоднократную помощь.
Выполнил все Ваши рекомендации и все отлично получилось.
Еще раз спасибо за участие.

Re: [? RUS]: Can't connecting to MAGELIS XBT-P022010 panel

Posted: Mon Jun 13, 2011 3:08 pm
by litos97
Hi there, I´m trying to dowload a backup from XBT panel (PM0207010) but I have a problem, when I conect to XBT-panel the software XBT L1000 detects the panel ok, but It can´t dowload the project and shows this message "Application format not recognized". I was talking with the Schneider support people, and they said than, is obligatory to use the same version of XBT L1000 was used to develop the application. I´ve had tried with these versións of XBT L1000: V3.30, V3.70, V3.80, V4.2, V4.42, V4.48, V4.50 and the last one V4.51, and I see the same error message.

I only need to try with versión V4.30 and V4.40, Is there any link to download this version, please? I searched in the forum and google, and no found. If somebody needs the version I´ve tried yet, I can upload here.

Thank´s in advance.

Re: [? RUS]: Can't connecting to MAGELIS XBT-P022010 panel

Posted: Thu Jun 16, 2011 6:51 am
by vlad2006gr
This is not related to the version of the program.
Version of the above can download a draft loaded with the old version. Use the XBT-L1000 4.51 Pro download backup.
This may be related to the Modbus protocol.
Read schneider info:
http://www.global-download.schneider-el ... Cindex.nsf
Inform about the results.

Re: [? RUS]: Can't connecting to MAGELIS XBT-P022010 panel

Posted: Wed Jul 20, 2011 10:48 am
by litos97
I´m sorry so much time without see this forum.

Thank you very much for your information, vlad2006gr. You have more knowledge than the support people. I´ve test this, with some protocols Unitelway, Modbus, Jbus, .... and you must install the communication protocol with plc in your laptop XBT-L1000, if you want upload a project from XBT. When the XBT starts, you can see the name of protocol installed inside of XBT terminal.

Now my problem is not the version of XBT-L1000, now I need the protocol driver XBT-L1000 for siemens s7 (3964(R) S7). This one, is not included with XBT-L1000, this is an additioal software purchased separately. Do you know if is it available somewhere ????

Thank´s in advance.
Litos97.

Re: [? RUS]: Can't connecting to MAGELIS XBT-P022010 panel

Posted: Thu Jul 21, 2011 8:21 am
by litos97
I´m sorry for ask before search inside of CD with last version XBT-L1000 v4.51(PRO), it has included all drivers/protocols.

Thank´s for all.

Litos97.

Re: [? RUS]: Can't connecting to MAGELIS XBT-P022010 panel

Posted: Thu May 29, 2014 8:40 am
by mickyblu
Hello

Can you please re-upload the files for the program

XBT-L1000 4.51 Pro

It seems that the links are dead.

Thank you

Micky

Re: [? RUS]: Can't connecting to MAGELIS XBT-P022010 panel

Posted: Fri May 30, 2014 12:24 pm
by vlad2006gr

Re: [? RUS]: Can't connecting to MAGELIS XBT-P022010 panel

Posted: Wed Aug 13, 2014 3:30 pm
by belkacem
Thanks vlad2006gr :)

Re: [? RUS]: Can't connecting to MAGELIS XBT-P022010 panel

Posted: Mon Dec 01, 2014 3:55 pm
by teraret
Thanks