PLCforum.uz.ua

I need iFix SCADA software, please give me the links to download.

Thank you,

try this
ftp://ftp.indusoft.ru/GEFanuc_Products/
i dont know what is the language
then use the lic in the net up to 2-10-2008
also exists full lic for 3.5
most

Hello most
Please, you can upload IFix4.0 in rapidshare.com
Thanks.

most wrote:try this
ftp://ftp.indusoft.ru/GEFanuc_Products/
i dont know what is the language
then use the lic in the net up to 2-10-2008
also exists full lic for 3.5
most

-----------------

I was download, but I don't have key!
Can you help me, please?

3 files

1.i_fi_x4 it lasts up to 2008 (tested)
2. i_fi_x4 it lasts up to 2012 (not tested by me)
3.ifxx 3.5 (tested)
for 3.5 edit with notpad tke key.reg for your SO and put the file *.sys
in c:\windows\intellution for XP (for example) or c:\winnt\intellution for 2000

Thank you.
Good luck to you.

edit your key.reg
(for XP)
-----------------------
Windows Registry Editor Version 5.00
[HKEY_CLASSES_ROOT\.iekey]
"license"="C:\\Windows\\Intellution\\slapi.dll"
@=""
"license_file"="C:\\windows\\intellution\\license.SYS"
"license_id"=dword:00000
-------------------------------------
put the file licence.sys in folder windows/inteletion

in the folder "windows/intellution" exist one file with name "iKeyUpdate" . run it
open the file licence.sys (open in all files) and ok. it appears an error. ok

run ifix et voila !

most wrote:edit your key.reg
(for XP)
....

Hi mostrengo....

i saw your messages on plc.net.ru about iFix.

Is there another file (license.sys) which epires on 2151 ?

normally a license.sys can't be inserted in the ikeyupdate tool.
An ikey file can be inserted in the ikeyupdatetool, but only if the ikey update file is for the same dongle serial number.

Btw. your 3 first files (Rar with 3 files) are software licenses. The ikeyupdate tool is for hardware hasp dongles.

Do you have a hasp dongle image of that last license (valid forever) for v.4.0 ? Or if not at least the file of your last post (software license license.sys)

Normailly i make dongle image form hasp4 dongle or emulated it with a dongle emulator or use a software license file like yours.

thx in advance,

monty

olá monty, you recognized me of another forum !
I do not have license to year 2151
I do not have original hasp dongle or emulated.
After some attempts I got the license using the program "iKeyUpdate"
my programes 3.5 and 4 i download it by emule.
sorry I cannot help you.
best regardes

most_trengo

most wrote:olá monty, you recognized me of another forum !
I do not have license to year 2151
I do not have original hasp dongle or emulated.
After some attempts I got the license using the program "iKeyUpdate"
my programes 3.5 and 4 i download it by emule.
sorry I cannot help you.
best regardes

most_trengo

hey most,

indeed another good forum

i previously saw in one or two replys above a message of you with 2 screens attached in in one screen (think the last) the license was until 21xx somewhere. (with other words a permanent license)

So you used the license.sys file with the ikeyupdate tool ?
Which license.sys file may i ask ? Is that file also located in your 3.5/4 file download ? Normally you can't use that license.sys in the update tool.
The license.sys is the soft license which can be installed with the .reg file.

Anyway there a new version 4.5 comming
with multi monitor support etc.....

greets,

monty

Hi friends,
..."another good forum" ... ?

Is possible to know the address ?

thanks

PLC_ITA wrote:Hi friends,
..."another good forum" ... ?

Is possible to know the address ?

thanks

the other forum has little PLC (almost nothing), is dedicated to EDA...
http://www.edaboard.com/
this http://plc.net.ru/ is the greater for PLC
most

Hi monty_burns_007,

Can you send me dump file of iFix 4.0 dongle?
Thank you very much,

most wrote:try this
ftp://ftp.indusoft.ru/GEFanuc_Products/
i dont know what is the language
then use the lic in the net up to 2-10-2008
also exists full lic for 3.5
most

Thank "most" for link. But I need password for IEC.zip in "ftp://ftp.indusoft.ru/GEFanuc_Products/ ... /Matrikon/". Would you send me?
Thank.

Where can I get myself a nice License.sys file to full activate Ifix4.0??

All links appear to be dead.

PLCUSER wrote:Where can I get myself a nice License.sys file to full activate Ifix4.0??

All links appear to be dead.

Link_is_Dead :(/ifix4.rar

rar pass: dibolo

Proficy - KeyDiag: Version 4.0.5
-----------------
Customer Name : 228274:GE Fanuc Auto
Warranty Number : Z‡пBс»&V
Expiration Date : Saturday, August 18, 2007 < -- ?????????


this key can active ifix4

but you can not use other pcl except GE plc

some function has been forbidden!

Hi, I want the download link for ifix 3.5.
Does anyone have it?
Please send me.