[?]: BACK UP KEY for a ABB digivis scada software

saul moreno · Post by **saul moreno** » Mon Jun 18, 2012 9:15 pm

Hello every one
I need some help, I need to back up a USB license, for a ABB digivis scada software
please any advise

thanks

Linkinx64 · Post by **Linkinx64** » Tue Jun 19, 2012 10:32 am

Digivis using HASP dongle, so you can try to dump the dongle as it is described in the topic below:

viewtopic.php?f=7&t=13472&start=50#p46338

Just skip the 9th step.
P.S. Upload your dongle dump (.REG or .FST) on forum when finished.

saul moreno · Post by **saul moreno** » Wed Jun 27, 2012 3:08 am

hello just started again with the deal,
I am not sure wich file downlad on the hard lock amulator
on this site
http://www.eplan-eb2.ys168.com/

thanks

Linkinx64 · Post by **Linkinx64** » Wed Jun 27, 2012 2:20 pm

This one:

saul moreno · Post by **saul moreno** » Fri Jun 29, 2012 12:35 am

Some thing happen and I can`t see any thing
on the usb stick, but i think the license is there,
only the pc with the software makes the usb work
any other pc, dont even sees it as drive,

any idea?

Thanks

Linkinx64 · Post by **Linkinx64** » Fri Jun 29, 2012 3:47 am

But HASP dongle should not be detected as a drive...
Dongle usually requires a driver to be installed to the system. Driver software supplied with DigiVis.

saul moreno · Post by **saul moreno** » Thu Jul 12, 2012 7:35 pm

Linkinx64
I got spoke to digi vis people, and they are sending me the file,
now the question is, with this file installed on the operations pc, should I do the procedure to back up the usb,
or should i back up first with the procedure you said

thanks

Linkinx64 · Post by **Linkinx64** » Fri Jul 13, 2012 3:56 am

Hi

What kind of file they're sent? I don't know it.
Backup USB first and upload to let us see it

saul moreno · Post by **saul moreno** » Fri Jul 13, 2012 6:18 pm

hi
they will send a file that have to be install on the pc with tha aplication (scada) to work, the deal is I have try to run TORO and I can`t see any thing,
I guess with this file will make it work, because I install the usb on the aplication and it does not work,
do you think. I need to back it up when I get this file?

Thanks

Linkinx64 · Post by **Linkinx64** » Mon Jul 16, 2012 9:05 am

What is a file that makes Digivis working can be?
Digivis is activated by insert dongle to the USB hole or LPT port. No additional files required.
If this is not "License mode" patch... I have no idea what "digivis people" can give you else.
Upload when you get it. A very interesting!..

saul moreno · Post by **saul moreno** » Sat Oct 06, 2012 12:32 am

Linkin64

How can I up load the file i got, to see if you can find some thing

Thanks

Linkinx64 · Post by **Linkinx64** » Sat Oct 06, 2012 5:47 am

http://www.4shared.com/
https://rapidshare.com/
etc. for your convenience.

saul moreno · Post by **saul moreno** » Fri Feb 08, 2013 6:39 am

Hello here is the file they send me
I hope you can help me
http://www.4shared.com/file/EK09K9wN/F2k.html

Thanks

PLCforum.uz.ua

[?]: BACK UP KEY for a ABB digivis scada software

[?]: BACK UP KEY for a ABB digivis scada software

Re: [?]: BACK UP KEY for a ABB digivis scada software

Re: [?]: BACK UP KEY for a ABB digivis scada software

Re: [?]: BACK UP KEY for a ABB digivis scada software

Re: [?]: BACK UP KEY for a ABB digivis scada software

Re: [?]: BACK UP KEY for a ABB digivis scada software

Re: [?]: BACK UP KEY for a ABB digivis scada software

Re: [?]: BACK UP KEY for a ABB digivis scada software

Re: [?]: BACK UP KEY for a ABB digivis scada software

Re: [?]: BACK UP KEY for a ABB digivis scada software

Re: [?]: BACK UP KEY for a ABB digivis scada software

Re: [?]: BACK UP KEY for a ABB digivis scada software

Re: [?]: BACK UP KEY for a ABB digivis scada software