PLCforum.uz.ua

maher

Excuse me , can do i transfer for the program by using prosave under windows ?

Maher

maher

Hi all

i need the the cable pin out to communicate between the pc and micromaster vector drive by using drive monitor, is it similar as the simovert drive cable pin out ???
Regards

Maher

maher

I wait for your reply

maher

Thanks a lot for your tips

could you choose for me the part number for RS232/PPI adapter to order it from siemens ( 6SE7901-3BF30-0XA0 OR 6ES7972-0CA10-0XA0 ), please ?

Maher

maher

No, Maher. You can not use USB adapter becouse it needs 24VDC from PLC/HMI side and only CPU-DP ports and advanced HMI ports provide this 24VDC. Use 232/PPI adapter (you can use Profilic USB/232 converter if your laptop has no serial ports). It work, tested. Excuse me , so can i use the 232/ppi ada...

maher

Hi all
how could i upload the program from cpu 314-1fm by using usp adapter ?

Maher

maher

Hi, The method I use is with a USB to USB transfer cable. You can get a Belkin one which will definately work. I use a clone type but whichever one you choose make sure you don't use the cables USB driver, use the USB Bulk Driver that is on a WinCC disk. Just set the transfer mode at the panel to b...

maher

HI
I'll use the prosave program, But i need to know the details about the communication cable between pc and touch screen ( serial ( via RS232/PPI MULTI-MASTER CABLE )).

or can i use the USP to MPI adapter to establish the communication between PC & SCREEN.

Please, urgently.

Maher

maher

Hi all Please, I have siematic panel TP177A 5.7 ( 6AV6642-0AA11-0AX1 ), I need to upload the program from the previous panel and download it to the new one only uploading and downloading . Please, tell me the required cable ( pin out ) to do this , the procedures of uploading and downloading , and t...

maher

usb to mpi adapter

maher

But i haven't got the program which in the cpu , so i am very scary to do the prvious steps .
I want in the first upload the program to get the original copy , after that i can change any thing .

If these steps only to get the program inform me to start to execute it

Maher

maher

sania wrote:change "set pg/pc interface " from mpi to tcp/ip & your tcp_card

Excuse me when i'll transfer from mpi to tcp/ip so i will use the profinet port , thats right or wrong?
if right how can i get the address for my pc to communicate with the cpu.

thanks a lot
Maher

maher

Hi all when i tried to go online with plc s7 319 2DP/PN , I got the below message: Upload station to pg ( 33:17075 ) online: The local MPI address for the programming device / pc is higher than the maximum node address or the the wrong transmission rate or wrong interrupt is set . so what can i do ?...

maher

Help please
Maher

maher

I used this program but no result, can you tell me the way of usage please

Maher

maher

Hi all
I need to upload the program from the protected ( CJ1M-CPU22 ), but when i tried to upload it the following message was appeared (

can not upload program UM read protected

, But I cann't get the password , so what can i do for that.
I need the reply urgently please.

Maher

maher

Hi

Please i want to know if the previous connection is suitable for this type of cpu51 or , it will need adapter ?????

please i am in bad need of the reply urgently

Best regards
Maher

maher

Please no time
I wait the reply urgently

Best regards
Maher

maher

Hi all it is the first time for me to use PLC OMRON type ( CQM1H-CPU51): I am working by CX programmer 8.1 , and the cable which assigned in this site , but i remarked that when i am trying to online the program doesn't show this PLC type and the connection would be failed , After that i make updati...

maher

Hi all

please can any one show me pin out for cable to conncet the pc to CQM1H-cpu51???

Best regards
Maher

maher

Hallo

i need the pin out also for the connection between the PC & MASTERDRIVE MC

regards
Maher

maher

Please i need help

maher

what is your opinion Umencho?

regards
Maher

maher

Hi
the uploaded cpu connected with [ profibus2 ( masterdrives , ET200S STANDARD ) AND MPI ( CONNECTED with the second cpu which has the same type )

the second the cpu connected with [ profibus1 ( ET200S STANDARD , MICROMASTERS 440, HMI SIEMENS )]

OK

regards

Maher

maher

Hi Umencho i have two cpu s7 315-2dp connected in the same profibus , according to your opinion , i installed the DRIVE ES ( HF1_zu_DriveES_Basic_V5.1SP1 ) after that i could make uploading for one of these cpu which is connected ( master drive, ES200 ) but the second cpu when i tried to upload it t...

maher

Hallo I was trying to upload the program from cpu siemens s7-315 2dp with profibus network but during the uploading process the follwing message was appeared ( uploading station to PG (13:77)) [ (2000) error while uploading the configuration to the programming device (PG) . do you want to continue? ...

maher

Hi all i faced problem when i was trying to download the new parameter to lenz drive servo type i remarked that the new parameter didn't save or not downloaded on in the drive ( i knew that by my self by seeing the code 5 no difference happened on it because i changed it. so can any one tell me the ...

maher

Hi The steps for uploading : I tried to upload the program from the cpu 313 with MC flash card but the result as before ( UPLOAD STATION TO PG ( 13:44 ) ONLINE CPU TYPE 6SE7313-1AD03-0AB0 V1.0.0 UNKNOWN. ) BUT when i go to online without uploading no problem happened and also i can make downloading ...

maher

Thank you very much Mr. comod

now the new software version is running .

thanks a lot

Best regards

Maher

maher

Or look at http://www.automation.siemens.com/WW/forum/guests/PostShow.aspx?PostID=61564&language=en Best regards, Umencho Hallo according to your link i decided to upgrade my software from V5.4+SP3 to V5.4+SP5 but after loading the service back file SP5 from the siemens site ( SIMATIC_S7_STEP7_V54_...

maher

thanks a lot

i will check these procedures

thank you very much

Maher

maher

Hi I have siemens cpu 313 with MC flash card , when i tried to upload the program the following message appeared : UPLOAD STATION TO PG ( 13:44 ) ONLINE CPU TYPE 6SE7313-1AD03-0AB0 V1.0.0 UNKNOWN. The software which i used is simatic manager step7 v5.4+sp3 So what does it mean and what can i do ? pl...

maher

Hi all
i can't activate the software , so i need the crack for it please

best regards

Maher

maher

Hi all I have allen-bradly plc type slc 5/04 cpu + device net module + 3 I/P module + 1 O/P module + 2 counter module i need to upload, download and monitor the program, but i don't know which version should i use from allen bradly softwares versions . or all can i use ?????????? (h) Best regards Ma...

maher

Hi all
i have the ( drive monitor 5.4 sp1 ) software and i need the specification for the communication cable between simovert drive and my copmuter .

also i need the procedures to upload the parameters from the drive & the steps to download the parameters to the drives

best regards

MAHER

maher

Hi all
thank you very much about your supporting for my problem , i found out the reason which energize this , it is the baud rate which i exchanged it from 9600 to 19200 .

thanks a lot

best regards

MAHER

maher

HI all thanks for your attention but i checked the communication setting when the touch screen rebooting but i didn't find any difference according to another one but i remarked that ( the communication led { green led} which is behind of the touch screen is blinking ) so what is the reason for that...

maher

Hi all i have a problem in touch screen allen_bradley type (panel view 550), the problem as following: - when i turned on the power on touch screen , the touch screen was reboted normally but the whole of number in touch screen was appeared by this shape ####### and ( panel view offline ) alarm was ...

maher

Thanks for this program i install the program but when i start the program it asked me about the license and this error message was appeared for me also [ error max40.35 the EPLAN5 program cannot be started with system EPLAN21 engineering suit ] but the way of using the crack file is not clear for m...

maher

what can i do?

i am disappoint about this drive

MAHER

maher

Hi all
i am trying to find any information to illustrate the whole of parameters of this type of lenze drive

i need to use servo lenze drive 9300 to make a homing for the motor

how can i do it ?
best regards

MAHER

maher

i know this site but it hasn't forum to ask him as this site.
i need site has aforum to contact him as this site

best regards

maher

maher

Hi all
i need any site as your site but specialist in lenze drives to understand every thing about it.

thanks alot

maher

maher

hi all i downloaded the wincc flexible 2008 from the current links here 4 monthes ago, and i made more of projects on it . but yesterday when i opened the program something was happened: _ the program was opened after that i selected the project which i wanted to open it ... but the project wasn't a...

maher

thanks alot
maher

maher

Hi all it is first time for me to create the network consist of plc S7(315-2DP) and drive lenze (9300 vector). but in the fact i haven't any information about the data transfering between the plc and drive to control on it. please i want to learn the steps to make it and applications to demonstrate ...

maher

hi all i am in bad need of signalizing the difference between these softwares in useing, wincc v6 software and wincc flexible 2005 or 2007 so it's first time for me to use anyone of them ,i try to learn any of each other so which do you prefer to start to learn from each other? best regards maher

maher

after setup this file the same message is appearing for me 29 left for evaluation
so what can i do
best regards
maher

maher

hi all
i need the manual for this software
please

maher

maher

hi sir
thanks alot for your information, but i need the manual for it
can you give me that ?
thanks

maher

Search found 105 matches