Search found 172 matches

by omar zedan
Tue Aug 28, 2012 5:47 pm
Forum: SIMATIC HMI
Topic: [?]: WinCC Activation SP2 ?
Replies: 1
Views: 3363

[?]: WinCC Activation SP2 ?

Dear All
I install WinCC V6.0 SP2 and try to activate it but it still demo.
thanks
by omar zedan
Wed Aug 08, 2012 5:05 pm
Forum: Other PLC
Topic: [?+]: ABB red triangle
Replies: 2
Views: 1891

Re: [?]: ABB red triangle

Thanks friend
by omar zedan
Tue Aug 07, 2012 8:50 pm
Forum: Other PLC
Topic: [?+]: ABB red triangle
Replies: 2
Views: 1891

[?+]: ABB red triangle

Dear All
How can I delete the red triangle from hardware (Modules) of ABB AC800 M Builder?
Note1:- the error mesage is Wrong module type (I use DI801 and define DI801 in software).
Note2:- the module work correctly in another PLC also I use Clear Latch unit Status BTN.
by omar zedan
Sun Jul 08, 2012 10:59 am
Forum: Other PLC
Topic: [?]: analog input in ABB Compact control builder 800m
Replies: 3
Views: 2363

Re: [?]: analog input in ABB Compact control builder 800m

how can I make the channels of AI801 analog input module read 4-20mA from 4-wire transmitter?
by omar zedan
Sun Jul 08, 2012 4:46 am
Forum: Other PLC
Topic: [?]: analog input in ABB Compact control builder 800m
Replies: 3
Views: 2363

[?]: analog input in ABB Compact control builder 800m

Dear All I have in compact control builder AC800M software In hardware config. of analog input module AI801 In setting tab parameters called (Activate channel1....Activate channel2......Activate channel3.............................Activate channel8) and the value of this parameters are true. What d...
by omar zedan
Fri Jul 06, 2012 7:25 am
Forum: Other PLC
Topic: [?]: connect 4-20 m to ABB analog input module AI801
Replies: 5
Views: 2905

Re: [?]: connect 4-20 m to ABB analog input module AI801

Hi I fully understand you, but my problem is:- I have (8 channel) AI801 analog input module. before connecting Analog input:- I musear the voltage between N+ and N- (where N may be any Channel from 1-->8) and it will be 24Vdc (the channels are source). therefore I cannot connect my signal to this ch...
by omar zedan
Thu Jul 05, 2012 11:14 am
Forum: Other PLC
Topic: [?+]: AC800M profibus module
Replies: 4
Views: 2337

Re: AC800M profibus module

dear Linkinx64 Thank you so much
by omar zedan
Thu Jul 05, 2012 11:08 am
Forum: Other PLC
Topic: [?]: connect 4-20 m to ABB analog input module AI801
Replies: 5
Views: 2905

Re: [?]: connect 4-20 m to ABB analog input module AI801

Dear Linkinx64 I do not fully understand you, I have (controller, digital input module DI801, digital output module DO801 and analog input module AI801)the problem in analog input module is that I have four wire flow meter (2 wires for power and 2 wires for return signal (4-20 mA)) and I afraid from...
by omar zedan
Thu Jul 05, 2012 10:35 am
Forum: Other PLC
Topic: [?+]: AC800M profibus module
Replies: 4
Views: 2337

Re: AC800M profibus module

I have ABB 3 pressure transmitters (266 gst 2600)(profibus not 4-20mA) and I need to read them in PLC.
Which module should I use???
Thanks
by omar zedan
Thu Jul 05, 2012 10:26 am
Forum: Other PLC
Topic: [?+]: ABB AC800M terminators
Replies: 2
Views: 1982

Re: [?+]: ABB AC800M terminators

Thank you very much
by omar zedan
Wed Jul 04, 2012 7:09 pm
Forum: Other PLC
Topic: [?]: connect 4-20 m to ABB analog input module AI801
Replies: 5
Views: 2905

[?]: connect 4-20 m to ABB analog input module AI801

Dear All I have AI801 analog input module(8 channel) in my rack and when i use AVO meter to read voltage between + and - for each signal I read 24Vdc, my signals are 4-20 mA how can I connect my input to this channels??? (Must I use safety barrier ????) Note:- I set the input as 4-20 mA in software....
by omar zedan
Wed Jul 04, 2012 6:55 pm
Forum: Other PLC
Topic: [?+]: AC800M profibus module
Replies: 4
Views: 2337

[?+]: AC800M profibus module

I have 3 profibus ABB prussre transmitors (profibus),
Can any one tell me if the ABB has a profibus module????
thanks
by omar zedan
Wed Jul 04, 2012 6:52 pm
Forum: Other PLC
Topic: [?+]: ABB AC800M terminators
Replies: 2
Views: 1982

[?+]: ABB AC800M terminators

Dear All
I need 2 terminators in AC800M rack (one of them like parallel port and the other a small connector)
Can I make them by myself???
thank you
by omar zedan
Tue Jul 03, 2012 6:07 pm
Forum: Other PLC
Topic: [?]: connecting ABB panel 836 with plc ac800m (851) through
Replies: 3
Views: 2183

Re: [?]: connecting ABB panel 836 with plc ac800m (851) thro

Dear Linkinx64
I am sorry I was used my friend cable and it was straight (not crossover) :oops:
Now i replace the cable and every thing ok.
Thank you very much.
by omar zedan
Tue Jul 03, 2012 2:11 pm
Forum: Other PLC
Topic: [?]: connecting ABB panel 836 with plc ac800m (851) through
Replies: 3
Views: 2183

Re: [?]: connecting ABB panel 836 with plc ac800m (851) thro

I use cross cable and connected directly
by omar zedan
Tue Jul 03, 2012 12:27 pm
Forum: Other PLC
Topic: ABB panel 836
Replies: 0
Views: 1434

ABB panel 836

Dear All
How can I connect plc AC800M and panel 836?
-I connect ethernet cable.
-I defined and connect variables in access variable(MMS tab)
-I give an IP address to the plc (in 2 places Ethernet (setting tab) and cpu properties (identify))
Thanks
by omar zedan
Tue Jul 03, 2012 12:10 pm
Forum: Other PLC
Topic: [?]: connecting ABB panel 836 with plc ac800m (851) through
Replies: 3
Views: 2183

[?]: connecting ABB panel 836 with plc ac800m (851) through

Dear all What i need (as a setting in software)for connecting panel 836 with plc ac800m (851) through TCP/IP ? -I connected port 1 in plc to the panel using ethernet cable. -I define variables in MMS tab in access variable. -Set the IP for ethernet port (in 2 places (Ethernet port in setting tab and...
by omar zedan
Sat Mar 03, 2012 5:46 am
Forum: Industrial network
Topic: [?]: need any info about Keba CP033/Z, TSPX 280 HMI
Replies: 2
Views: 9319

Re: [?]: need any info about Keba CP033/Z, TSPX 280 HMI

Do you have them software????
Thanks
by omar zedan
Sat Mar 03, 2012 5:45 am
Forum: Industrial network
Topic: Request: Software and Manuals for KEBA
Replies: 0
Views: 5071

Request: Software and Manuals for KEBA

Do you have the software needed to program KEBA hardware??
thanks
by omar zedan
Wed Nov 02, 2011 7:59 pm
Forum: Industrial network
Topic: [?]: need any info about Keba CP033/Z, TSPX 280 HMI
Replies: 2
Views: 9319

[?]: need any info about Keba CP033/Z, TSPX 280 HMI

Hi all
I have KEBA CP033/Z PLC and KEBA TSPX 280 HMI, Dose any one have any information about them
Regards
omar
by omar zedan
Mon Oct 24, 2011 3:32 am
Forum: Allen-Bradley (Rockwell Automation)
Topic: [?]: Servo motor & RSLogix5000
Replies: 2
Views: 2233

Thanks

thank you so much
by omar zedan
Sat Oct 22, 2011 7:19 am
Forum: Allen-Bradley (Rockwell Automation)
Topic: [?]: Servo motor & RSLogix5000
Replies: 2
Views: 2233

[?]: Servo motor & RSLogix5000

Hi all In Old tires factory they have 2 machine used for building tires (stage 1 and stage 2) in each machine they have Westinghouse PLC and 4 DC drivers and 4 DC motors. The first Motor is 7 HP DC motor (main motor). The other 3 motors are 0.75 HP. They decide to replace the PLC, Motors (with Servo...