PLCforum.uz.ua

Hi, I have a machine with AB control logix 5550 cpu and a panel view 2711p. I need to connect a pc to be able to monitor, whatever it is in the existing panel view. What software do i need (configuration and run time)? is it factory talk view machine edition? I have the panel view file, is it possib...

i am looking for pid cascade literature, i found this thread. but the link is dead. could anyone share it again?

could anybody re-load cs3000 again please?
the above one is not active anymore.

Dear sventek,

i download your fb to the cpu and test fb15 to convert dint to real and fb16 to get back, but the result is not the same. i think your fb doesn't work. do you upload this fb from cpu 115u?

dehell is right this cable is not a tty cable. it is used only with pg7xx.
i think what indian post is the cable configuration to connect pg7xx with s5 cpu.
i guess i have to find a tty cable. thank you everybody.

may be no one have the installation disk.
But i am sure someone has it in their plc program.
could anyone just transfer this fb15 to fb21 to a new s5 program and upload it here? i really need it.

Dear all,

i got 6es57342bf00 (s5 tty cable 5m).
i want to connect to my pc (9 pin).
this connector has a 25 pin.
i wire:
i got plc time out.
has anybody use this cable with 9 pin connector before? what do i miss here?

Dear all, This sound pretty stupid, i lost my soft copy of S5 cpu 115 (6es59427ub11) program, both in my computer and in my plc. but i still have my hard copy. I re-type everything until i came up to S5 FB 15 to 21 which i do not have it. I have search everything i could but only to find it is : 6ES...

Hi,

i got a cj1m cpu 11 plc. i got a *.cxp file.
but when i open this file with cx-programmer, it was protected.
i do not have the password.
anybody know how to unprotect it?
i need to do some modification.

Dear Avtfree,

thank you very much.

could anybody share c200h cpu21 manual? i have search but could not find one. i got this old plc, it is broken now. i got the program hard copy in ladder. my problem is i got this "fun 11" instruction. i guess it is a keep relay (set reset relay). i just don't know which input is set and which one i...

turn off op7 press key: "esc" + "up", turn on op7. do not let the button go for 2 second. then let go the button. use prosave to download. good luck

i have download this software.
but i could not open ladder diagram for kv-300. any idea?
thanks in advance

I have OP17. it is damage now. i am planning to use winCC flexible RT with PC. i got an old file with extension pda, par, rpa,arh, mdx, clip organizer media package. i do not know what it is. when i try to open *.pda file using Protool V6.0 SP2. The first error message is as follows "Your project wa...

As we know in industrial application there are still lots of equipment still use serial port. today's laptop only come with usb, no real serial port h/w. using a usb to serial port converter, sometimes work but mostly don't. my question is does anybody have experience with docking station for laptop...

Hi,
anybody could share comprofibus V3.3 (com profibus v3.3)?
i have a configuration which was made in V3.3, i was unable to open it with V5.1. thanks in advance

I have install profibus scope successfully. but when i open it, i have a message: channel to card could not be open! check your setting and card installation! software works in off line mode. my system: - windows XP sp3 - cp 5511 when i use simatic manager, using this cp5511 i could connect to 315 P...

i have install comprofibus v5.1 with hf1, hf2, and hf3. but i still could not connect to im308c. while using cp5511 connected to im308c and using set pg/pc to test the bus, i could not get any result. but hen i disconnect cp5511 from im308c and do diagnose from set pg/pc everthing is ok. does this c...

Dear all, i just bought a second hand cp5511, but i don't have the sofware cd. i use the CP to communicate with S7 plc with no problem. I have simatic S7 manager V5.4 and simatic net 2006 installed on my laptop. My problem is when i need to connect my CP with IM308C (S5 PLC) with comprofi bus, it sa...

I got it,

My program only have 2 IEC function block. instead of writing 2 at IEC LEN in OB100, i wrote 8. after changing it to 2 everything is fine.

both of my hw config are the same
i have downloaded everything into both of my cpu
i have tested both termination of my bus.
still could not get it right

I am installing software redundant, after downloading i got this problem: 1. Both CPU in stop mode: - at first IM153-2 SF blink, ACT off. - at second IM153-2 every thing is OK, ACT on - SF and BF LED at both CPU are off 2. Switch CPU to RUN mode: - SF LED on at both CPU - at first IM153-2 SF blink, ...

i mean some of the books are banned, like serial port and parallel port.

Hi, a very good book indeed, but Almukhtar could you please re-load the book in other name may be? i coul not download it since it is banned. thanks.