Search found 91 matches

by kriztof
Mon Oct 20, 2014 11:54 am
Forum: Other (only about CAD and Soft)
Topic: CRACK AUTOMATION STUDIO P6 32 B
Replies: 14
Views: 18040

Re: CRACK AUTOMATION STUDIO P6 32 B

Thanks chispa1971a, but I get CRC error, could you reupload part1 ? PAS32IZFTP60010932.part01.rar: CRC failed in PAS32IZFTP60010932\Data1.cab. The file is corrupt PAS32IZFTP60010932.part01.rar: Unexpected end of archive PAS32IZFTP60010932.part01.rar: Packed data CRC failed in PAS32IZFTP60010932\Data...
by kriztof
Sun Jul 20, 2014 7:40 pm
Forum: Siemens Hardware & Software
Topic: CP342-5 DC/DC converter
Replies: 0
Views: 2997

CP342-5 DC/DC converter

Hi
Does anyone know where to find original Aucon AC6A11-03 DC/DC converter or some suitable replacement?
CP342_top
Show
Image
by kriztof
Thu Feb 06, 2014 6:09 pm
Forum: Drivers and Inverters
Topic: (offtop)
Replies: 1
Views: 1844

Re: Backup parameters for Emerson unidrive

Try serial communication. The Unidrive SP has a standard 2-wire EIA485 interface (serial communications interface) which enables all drive set-up, operation and monitoring to be carried out with a PC or controller if required. On panel check/set these parameters: 0.35 Serial mode 0.36 Serial communi...
by kriztof
Sun Oct 06, 2013 8:44 am
Forum: Siemens Hardware & Software
Topic: [?]: install WinAC RTX inside VMware
Replies: 3
Views: 6954

Re: [?]: install WinAC RTX inside VMware

I tried to test WinAC inside VirtualBox. It is terribly slow, impossible to work. I think real time system is to much for virtual machine system.
by kriztof
Fri Sep 20, 2013 4:46 pm
Forum: Other PLC
Topic: Modicon TSX Micro Nano
Replies: 18
Views: 15815

Re: Modicon TSX Micro Nano

we ask it to a supplier and tey recommend TELTSXCUSB485 and TELTSXCRJMD25 It should works without problem. About the software PL707 only open *.PL7 files and the program code that client send to me is *.TSX. I worked a few times with TSX Nano (TSX 07) and PL707 Win software but always with my own c...
by kriztof
Thu Sep 19, 2013 9:05 am
Forum: Other PLC
Topic: Modicon TSX Micro Nano
Replies: 18
Views: 15815

Re: Modicon TSX Micro Nano

Original cable is TSX PCX 1031, you can also do it yourself. To build cable you need Male 8 pin mini DIN connector and RS485 converter - check pin-out in documentation. I recommend to use PL 707 Win
PL707 Win
by kriztof
Fri Apr 12, 2013 4:44 pm
Forum: SIMATIC system
Topic: Is it possible to share tags though Profibus on S7-300?
Replies: 1
Views: 1160

Re: Is it possible to share tags though Profibus on S7-300?

Check these functions:
SFC 14 "DPRD_DAT"
SFC 15 "DPWR_DAT"
by kriztof
Sun Feb 10, 2013 3:51 pm
Forum: Other (only about CAD and Soft)
Topic: Request: crack for Festo FluidSim 4.2
Replies: 7
Views: 13500

Re: Request: crack for Festo FluidSim 4.2

It looks this crack is for different version. I've tested with version 4.2 and it works very well.
by kriztof
Wed Jan 09, 2013 8:09 pm
Forum: SIMATIC system
Topic: [?+]: error connect cpu214 with PPI adapter
Replies: 9
Views: 2975

Re: [?+]: error connect cpu214 with PPI adapter

First, make sure your adapter is properly installed in system. In Windows 'Device Manager' under 'Simatic Devices' there should be listed 'SIMATIC PC USB adapter'. Next, check that 'PC Adapter(PPI)' interface is installed in Micro/WIN. If you still can't communicate, my idea is that you should check...
by kriztof
Sat Jan 05, 2013 2:19 pm
Forum: SIMATIC system
Topic: [?+]: error connect cpu214 with PPI adapter
Replies: 9
Views: 2975

Re: [?+]: error connect cpu214 with PPI adapter

It looks you have USB adapter.
Install SIMATIC PC Adapter USB Software V2.0
http://support.automation.siemens.com/W ... n/27062840
You should also update your firmware
http://support.automation.siemens.com/W ... n/14692974
by kriztof
Thu Jan 03, 2013 9:33 pm
Forum: SIMATIC system
Topic: [?+]: error connect cpu214 with PPI adapter
Replies: 9
Views: 2975

Re: [?]: error connect cpu214 with PPI adapter

Do you use Siemens PPI adapter or some Chinese equipment? Is your COM port integrated with motherboard or you have additional card? Check COM settings in BIOS/Windows, check PPI adapter speed selector. If possible test with another CPU. Read S7-200 System Manual http://support.automation.siemens.com...
by kriztof
Thu Dec 20, 2012 6:23 pm
Forum: SIMATIC system
Topic: Request: PC RS232 adapter V5.1 (6ES7972 0CA23 0XA0) driver
Replies: 3
Views: 5076

Re: Request: PC RS232 adapter V5.1 (6ES7972 0CA23 0XA0) driv

And other information: if you go to set PC/PG interface and tap to select tab you can see all interface installed from step 7 and when you mark on PC adapter you can see the next: Adapter for MPI/PROFIBUS net via USB interface of the PC I think there should be (must be?) description: Adapter for MP...
by kriztof
Wed Dec 19, 2012 6:23 pm
Forum: SIMATIC system
Topic: Request: PC RS232 adapter V5.1 (6ES7972 0CA23 0XA0) driver
Replies: 3
Views: 5076

Re: Request: PC RS232 adapter V5.1 (6ES7972 0CA23 0XA0) driv

You don't need special system drivers (I don't know if these even exist). Check your COM settings. Is your RS232 port integrated with your computer or do you use some kind of RS233 expansion card or USB/ExpressCrad/PCMCIA converter? http://support.automation.siemens.com/WW/llisapi.dll/csfetch/226115...
by kriztof
Fri Dec 14, 2012 8:58 pm
Forum: Other (only about CAD and Soft)
Topic: Request: crack for Festo FluidSim 4.2
Replies: 7
Views: 13500

Re: Request: crack for Festo FluidSim 4.2

Check this link for newest version: FluidSim 4.5d
But what about protection (Wibu key)?
by kriztof
Fri Dec 14, 2012 8:53 pm
Forum: Other PLC
Topic: Request: ladder builder for KV
Replies: 2
Views: 1997

Re: LINK: ladder builder for KV

Could anyone re-upload this software, please?
by kriztof
Tue Nov 27, 2012 6:04 pm
Forum: SIMATIC system
Topic: [?]: connecting output of PID FB41 with analog out PQW
Replies: 2
Views: 1929

Re: S7 PID

I think you should use LMN_PER output.
by kriztof
Tue Oct 16, 2012 6:28 pm
Forum: Other PLC
Topic: how to understand fatek progam ?
Replies: 3
Views: 2064

Re: how to understand fatek progam ?

Without source project and electrical diagrams and with zero knowledge about machine it's difficult to completely understand this program :( Do you have some information about this machine e.g. manual, operator instruction, safety instruction etc. Your machine is equipped with Weintek HMI panel. Did...
by kriztof
Wed Oct 10, 2012 5:21 pm
Forum: Other PLC
Topic: how to understand fatek progam ?
Replies: 3
Views: 2064

Re: how to understand fatek progam ?

Could you upload your project on different host?
by kriztof
Sat Sep 08, 2012 7:27 am
Forum: PLC's video
Topic: VIDEO Come learn FATEK-PLC in Arabic language
Replies: 1
Views: 5927

Re: VIDEO Come learn FATEK-PLC

Thanks, it is in Arabic language.
by kriztof
Fri Aug 24, 2012 12:29 pm
Forum: SIMATIC system
Topic: [?]: EXTERNAL POWER SUPPLY OF THE PC ADAPTER USB
Replies: 2
Views: 2901

Re: [?]: EXTERNAL POWER SUPPLY OF THE PC ADAPTER USB

Dear All, Have anyone any information, picture about EXTERNAL POWER SUPPLY OF THE PC ADAPTER USB (6ES7972-0CA00-0XA0)? How it is used? Probably it is ordinary power supply module with cable. I can't imagine something more fancying. You don't need external power for USB PC Adapter if you work with M...
by kriztof
Thu Aug 23, 2012 10:15 pm
Forum: SIMATIC system
Topic: [?]: Create MMC card with firmware for S7-300
Replies: 1
Views: 3365

[?]: Create MMC card with firmware for S7-300

Hi
Is it possible to create MMC card for updating operating system (firmware) using "Uwes S7 MMC Card Writer" (software tool)?
I don't have neither prommer nor PG, so I thought I can write KOMP_1.UPD file to MMC card (binary copying) using this program. Anyone tried this method?
by kriztof
Sun Aug 12, 2012 5:28 pm
Forum: SIMATIC system
Topic: [?]: S7-300 CPU314C-2DP LED Status
Replies: 3
Views: 2829

Re: S7300 CPU314C-2DP LED Ststus

I've checked my S7-314 and S7-315-2DP, and, yes it looks that DC5V is hardware signal. I'm not electronic specialist, but, for me there is DC/DC converter that changes 24VDC (power supply voltage) to 5VDC (logic supply voltage), and probably DC5V led is directly (or through some resistor) connected ...
by kriztof
Sun Aug 12, 2012 8:26 am
Forum: SIMATIC system
Topic: [?]: S7-300 CPU314C-2DP LED Status
Replies: 3
Views: 2829

Re: S7300 CPU314C-2DP LED Ststus

DC5V led means that there is 5V power for CPU and bus. IMO it is pure hardware signal, it doesn't depend on CPU state.
by kriztof
Wed May 30, 2012 5:20 pm
Forum: SIMATIC system
Topic: [?]: why my hardware configure can not monitor online
Replies: 3
Views: 2649

Re: [?]: why my hardware configure can not monitor online

Maybe you should install HW updates?
by kriztof
Tue Dec 13, 2011 5:32 pm
Forum: Other (only about CAD and Soft)
Topic: [?]: PcSchematic or Autocad Electrical?
Replies: 6
Views: 5594

Re: PcSchematic or Autocad Electrical?

WSCAD is powerful and not expensive, however it's hard to learn and use (WSCAD 5). I've seen working WSCAD 6 demo and it looked much better.
by kriztof
Sun Dec 11, 2011 9:00 am
Forum: Drivers and Inverters
Topic: F001 Fault after power On with micromaster
Replies: 1
Views: 3971

Re: F001 Fault after power On with micromaster

To reset the fault code, one of three methods listed below can be used: 1. Cycle the power to the drive. 2. Press the Fn button on the BOP or AOP. 3. Via Digital Input 3 (default setting) F0001 Overcurrent STOP Quit Remove fault and reset fault memory by - disconnecting the drive converter from the ...
by kriztof
Mon Oct 31, 2011 5:21 pm
Forum: Other (only about CAD and Soft)
Topic: request : automation studio 5.6
Replies: 1
Views: 2495

Re: request : automation studio 5.6

It would be sweet to get this, but for now, as I know, the only working versions are 5.0 and 5.2 (with minor problems, e.g. not working library).
by kriztof
Mon Oct 03, 2011 4:40 pm
Forum: SIMATIC HMI
Topic: Why "invisible mode" for any button DONT activate in wincc
Replies: 4
Views: 2767

Re: Why "invisible mode" for any button DONT activate in wi

Maybe buttons are covered by other object(s)? Bring them to front, also check layers.
by kriztof
Sun Sep 18, 2011 7:27 pm
Forum: SIMATIC system
Topic: [?]: view the content of local variables in STEP7
Replies: 1
Views: 1612

Re: [?]: view the content of local variables in STEP7

You can't access L Stack directly.
In my opinion the easiest way is copy temporary variables into appropriate bit memory area.
You can also stop CPU (eg. interrupt, error, breakpoint) and then check stacks in module information.
by kriztof
Fri Sep 16, 2011 8:55 am
Forum: SIMATIC system
Topic: [?]: MM440 profibus Communication
Replies: 1
Views: 1917

Re: [?]: MM440 profibus Communication

First, you try to read double word value (Real and IEEE are 32-bit) into single word (PZD is 16-bit).
Second, I think you have to use PKW mechanism instead of PZD data words.
Check this document
https://support.automation.siemens.com/ ... 0202_I.pdf
by kriztof
Sat Jul 09, 2011 7:11 am
Forum: SIMATIC system
Topic: [?]: MPI COMMUNICATION between cpu 413 & cpu 315
Replies: 9
Views: 4813

Re: PLCSIM

No, GD doesn't work with PLCSIM. These are available options for communication between multiple CPU modules: SFB8 "USEND" SFB9 "URCV" SFB12 "BSEND" SFB13 "BRCV" SFB15 "PUT" SFB14 "GET" SFB19 "START" SFB 20 "STOP" SFB 22 "STATUS" SFB 23 "USTATUS" https://support.automation.siemens.com/WW/llisapi.dll?...
by kriztof
Thu May 26, 2011 6:57 pm
Forum: Other (only about CAD and Soft)
Topic: Request: crack for Festo FluidSim 4.2
Replies: 7
Views: 13500

Re: Request: crack for Festo FluidSim 4.2

I have access to full copy of Fluidsim 4.2 and wibu key, anyone can make emulator for hardware protection?
by kriztof
Wed May 25, 2011 7:02 pm
Forum: Other (only about CAD and Soft)
Topic: Request: Eplan 5.7 Tutorial
Replies: 1
Views: 2089

Re: Request: Eplan 5.7 Tutorial

I have never get any tutorial, there is only Docucenter witch is not exactly tutorial but it's helpful.
by kriztof
Mon Apr 25, 2011 7:17 am
Forum: SIMATIC system
Topic: [?]: How connect PG2000 to s5-115u ?
Replies: 4
Views: 3784

Re: [?]: How connect PG2000 to s5-115u ?

I'm afraid the software PG2000 which i have is not good!
This works perfectly
viewtopic.php?f=30&t=12575&hilit=pg2000
by kriztof
Sun Feb 13, 2011 9:09 am
Forum: SIMATIC system
Topic: S5- 115U CPU-943B in Stop Mode With Error LED QVC and BASP
Replies: 6
Views: 5381

Re: S5- 115U CPU-943B in Stop Mode With Error LED QVC and BA

QVZ is triggered when CPU can't access I/O module (this error occurs if a module fails to acknowledge within 160 µs of being
accessed). I suggest you to create empty OB23 and upload to CPU. If CPU will run then you should replace faulty card. For detailed diagnostic you should check also ISTACK.
by kriztof
Thu Feb 10, 2011 10:58 pm
Forum: SIMATIC system
Topic: [?]: S5 95U various versions compasion
Replies: 5
Views: 3507

Re: [?]: S5 95U various versions compasion

I have practical experience with replacing basic unit for L2-DP Slave unit. By default additional interface is disabled so without parameterizing DB1 these units behave identically.
by kriztof
Mon Jan 31, 2011 8:59 pm
Forum: SIMATIC system
Topic: [?]: S5 95U various versions compasion
Replies: 5
Views: 3507

Re: [?]: S5 95U various versions compasion

Basically there are few types of 95U: S5-95U (basic unit) 6ES5 095-8MA0x S5-95U, SINEC L2 Interface (Profibus FMS) 6ES5 095-8MB0x S5-95U, Second Serial Interface 6ES5 095-8MC0x S5-95U, SINEC L2-DP Interface (Profibus DP Slave) 6ES5 095-8MD0x S5-95U, SINEC L2-DP Interface (Profibus DP Master) 6ES5 09...
by kriztof
Mon Nov 29, 2010 4:54 pm
Forum: SIMATIC system
Topic: [?]: My S7-300 PLC CPU 313C do not coming in RUN Mode
Replies: 1
Views: 1896

Re: S7-300 Problem

You have to use Step7 to access PLC diagnostics buffer. Connect to your PLC using MPI bus and then from Simatic Manager chose Hardware Diagnostics. http://support.automation.siemens.com/WW/view/en/2687356 https://support.automation.siemens.com/WW/llisapi.dll/csfetch/2687356/Diagnosepuffer_01_e.jpg
by kriztof
Fri Oct 15, 2010 8:28 pm
Forum: SIMATIC system
Topic: [?]: S7313c can't work without MMC
Replies: 9
Views: 8664

Re: [?]: S7313c can't work without MMC

Trafo wrote:Writing on MMC and reading from it is slow operation.
Typical MMC card like Kingmax 32MB in sequential read mode transfers 3126 KB/s and in sequential write mode transfers 1368KB/s, S7-314 has only 96KB integrated work memory. How long it takes to load program from card to work memory?
by kriztof
Fri Oct 15, 2010 3:47 pm
Forum: SIMATIC system
Topic: [?]: S7313c can't work without MMC
Replies: 9
Views: 8664

Re: S7313c download 2 error/ block/op.sys larg ...bottleneck

You can't use your PLC without MMC card. YES (no) MMC contains hardware configuration and user program. PLC loads config and blocks from MMC after power up. Notice, new PLC modules are not equipped with battery so how do you think they store program or configuration? Have you ever tried to load you...
by kriztof
Sun Oct 10, 2010 6:47 pm
Forum: Other PLC
Topic: [LINK]: Hilscher SyCon
Replies: 9
Views: 8055

Re: [Request]: Hilscher SyCon

Thank you very much, excellent work. :D
I built a new configuration and downloaded to the card. I will test whole installation as soon as possible.
Once again, great work Linkinx64 (clap)
by kriztof
Sat Oct 09, 2010 6:27 pm
Forum: SIMATIC system
Topic: [?]: S7313c can't work without MMC
Replies: 9
Views: 8664

Re: S7313c download 2 error/ block/op.sys larg ...bottleneck

Eng_Ali wrote: I use s7 313-5BF03-0AB0..without MMC and Step7 V5.4 SP4 with hardware updated
You can't use your PLC without MMC card.
Step7 loads your program to MMC card and then PLC loads its contents to RAM.