Search found 8 matches

by SergeyNG
Thu Jul 02, 2009 7:42 am
Forum: Other HMI
Topic: [?]: Cable V6-CP for Hakko MONITOUCH V606e.
Replies: 2
Views: 4560

А MJ1 выбран в качестве порта передачи данных? Скорость передачи какая установлена в панели?
Сам когда то делал кабель для V606e, точно не помню, но кажется надо на RS232 соединить 6(DR),7(RS),8(CS).
by SergeyNG
Tue Jun 30, 2009 3:34 pm
Forum: Other PLC
Topic: [LINK]: Mitsubishi A series motion controller software
Replies: 4
Views: 4390

Link_is_Dead :(/250329544/SW3RN.ZIP

After program installation run patch\patch.bat for installation of correct driver SSCNET
by SergeyNG
Wed Jun 24, 2009 3:44 pm
Forum: Other PLC
Topic: [LINK]: Mitsubishi A172CPUN motion controller O.S.
Replies: 12
Views: 9265

by SergeyNG
Thu Jun 18, 2009 9:00 am
Forum: Other PLC
Topic: [LINK]: Mitsubishi A172CPUN motion controller O.S.
Replies: 12
Views: 9265

Link_is_Dead :(/245840283/A172_OS.zip.html
MD5: 81E7002E3B8EC343E8B3208E77F4B537
by SergeyNG
Thu Sep 27, 2007 8:45 am
Forum: Other PLC
Topic: Request: B&R Automation Studio
Replies: 2
Views: 4610

in Russian wrote:Если программа заливалась Autmation Studio, а не PG2000, выгрузить не получиться.
В процессоре лежит только откомпилированный Automation Studio код.
by SergeyNG
Wed Aug 08, 2007 1:42 pm
Forum: Other PLC
Topic: [LINK]: GX IEC Developer V7.0 serial no
Replies: 9
Views: 17956

DimonS писал(а):
12000-40040-36498-70071-2096
Yasir Maqsood писал(а):
Need link for GX-developer IEC 7.00
http link:
http://www.induteq.nl/induteq/bestanden ... ren%29.zip
by SergeyNG
Tue Jun 26, 2007 2:24 am
Forum: Other HMI
Topic: [?]: How unlock password an ProFace GP2500?
Replies: 11
Views: 18367

For example.

Hex veiw project:
00000: 53 43 44 20 4C 6F 63 6B
00008: 8E 88 9A 8D 8B 48 01 3A

FF - 8E = 71 HEX to ASCII -> q
FF - 88 = 77 HEX to ASCII -> w
FF - 9A = 65 HEX to ASCII -> e
FF - 8D = 72 HEX to ASCII -> r
FF - 8B = 74 HEX to ASCII -> t

Password: qwert 8)

best regards
by SergeyNG
Mon Feb 26, 2007 7:53 am
Forum: Other PLC
Topic: [?]: B&R plc
Replies: 2
Views: 5337

By means of Automation Studio it is possible to program: - Controllers System 2003 - Controllers System 2005 - IPC2000, IPC5000 - Power Panel -, etc. products B*R The previous answer a little bit wrong. The project created in Automation will not open in PG2000. On the contrary, did not try, at once ...