Search found 182 matches

by dsekulic
Wed Nov 29, 2023 3:39 pm
Forum: Siemens Hardware & Software
Topic: S 400 PLC -Need help to have redundancy PLC with ET200
Replies: 4
Views: 1686

Re: S 400 PLC -Need help to have redundancy PLC with ET200

Hi,
If You use IM153-1 You are able to reach I/O modules just from one redundant CPU. With IM153-2 You can simultaneously connect to both redundant CPU-s
by dsekulic
Wed Nov 29, 2023 11:59 am
Forum: Siemens Hardware & Software
Topic: S 400 PLC -Need help to have redundancy PLC with ET200
Replies: 4
Views: 1686

Re: S 400 PLC -Need help to have redundancy PLC with ET200

Hi,
For this You need IM135-2 (6ES7153-2AR04-0XA0) SIMATIC DP, ET 200M Red. Bundle Consisting of: 2x IM 153-2HF (6ES7153-2BA10-0XB0), 1x bus module in/in (6ES7195-7HD10-0XA0)
Also You should have active backplane bus modules
by dsekulic
Sun Feb 12, 2017 11:35 pm
Forum: Other (only about CAD and Soft)
Topic: Help with EPLAN 2.6
Replies: 1
Views: 3219

Re: Help with EPLAN 2.6

Hi,
You can find links on:
viewtopic.php?f=7&t=24410&hilit=eplan+2.6
regards
by dsekulic
Fri Jan 20, 2017 2:47 pm
Forum: SIMATIC system
Topic: DBx.DBDxxx to output
Replies: 6
Views: 4390

Re: DBx.DBDxxx to output

Could You clarify Your problem. DBx.DBDx is DOUBLE WORD data, which is 32bits wide.
by dsekulic
Fri Jan 20, 2017 1:57 pm
Forum: SIMATIC system
Topic: DBx.DBDxxx to output
Replies: 6
Views: 4390

Re: DBx.DBDxxx to output

if You use STL than:

a DB1.DBX0.5
= Q0.1

Upper code You can easy convert to LAD or FBD

regards
by dsekulic
Sun Dec 18, 2016 4:55 pm
Forum: Other PLC
Topic: [Request] IEC104 slave simulator software
Replies: 2
Views: 3166

Re: [Request] IEC104 slave simulator software

Hi, You can find good simulator on: http://www.trianglemicroworks.com/products/downloads Software is not free, but You have test period (I think 21 days) Name of software is Test Harness In attachment You will find one Siemens test software for 104 protocol https://dl.dropboxusercontent.com/u/722394...
by dsekulic
Fri Nov 04, 2016 12:22 am
Forum: Simatic (Russian)
Topic: S7-PDIAG
Replies: 1
Views: 2156

Re: S7-PDIAG

Hi,
You need to install S7 PDIAG first.
by dsekulic
Sun Oct 16, 2016 10:55 am
Forum: Simatic (Russian)
Topic: PID-регулирование процесса в step7
Replies: 1
Views: 2249

Re: PID-регулирование процесса в step7

Hi,
You can find some examples and a lot of literature on
https://support.industry.siemens.com/cs/start?lc=en-US
in search put for example: PID control FB41
kind regards
by dsekulic
Mon Dec 21, 2015 9:10 pm
Forum: Other (only about CAD and Soft)
Topic: Dispalying page.row.column Cross reference in eplan
Replies: 2
Views: 2960

Re: Dispalying page.row.column Cross reference in eplan

Hi,
For this purpose You need plot frame with columns and rows. In following link You will find example with one plot frame with columns and rows.
link:
https://dl.dropboxusercontent.com/u/722 ... xample.fn1
regards
by dsekulic
Tue Dec 01, 2015 1:48 pm
Forum: SIMATIC system
Topic: [?]: s7 300 SF Red error
Replies: 5
Views: 3658

Re: [?]: s7 300 SF Red error

Hi.
If You use PLC without configured module (in HW config) You have SF LED for sure.
regards
by dsekulic
Sun Nov 29, 2015 6:07 pm
Forum: SIMATIC system
Topic: [?+]: S7 300 the module MMC is password protected
Replies: 8
Views: 9290

Re: S7 300 the module MMC is password protected

Hi, In following link You have description and two programs with description (unfortunately in Russian). In short You need to insert MMC in external USB card reader (important: do not format S7-MMC card). Start S7imgRD.exe to read image. Afterward start Unlocks7200and300.exe to unlock S7 program fro...
by dsekulic
Sat Oct 17, 2015 7:04 am
Forum: SIMATIC system
Topic: STL command list manual??
Replies: 2
Views: 2910

Re: STL command list manual??

https://support.industry.siemens.com/cs/document/31977679/simatic-s7-300-instruction-list-s7-300-cpus-and-et-200-cpus?dti=0&lc=en-US https://support.industry.siemens.com/cs/document/60109531/s7-400h-instruction-list-cpu-412-5h-pndp-414-5h-pndp-416-5h-pndp-417-5h-pndp?dti=0&lc=en-US https://support....
by dsekulic
Wed Jul 15, 2015 4:26 pm
Forum: Other (only about CAD and Soft)
Topic: EPLAN P8 1.7 connection numbering
Replies: 1
Views: 2183

Re: EPLAN P8 1.7 connection numbering

Hi,
In terminal properties under Function definition should stay N-terminal or PE-terminal or SH-terminal or you can make your own function definition. In this case terminals are not numbered in automatic numbering.
regards
by dsekulic
Thu May 07, 2015 5:20 pm
Forum: Other (only about CAD and Soft)
Topic: Eplan mounting panel problem
Replies: 4
Views: 6050

Re: Eplan mounting panel problem

Hi, Open Project Data -> Parts/Devices -> 2D panel layotut navigator. There You will find all parts which You have to put on panel. If You drag and drop parts from 2D layout navigator You will see green checkbox on placed element (that means that You place element on panel). Important thing is mount...
by dsekulic
Sun May 03, 2015 10:25 pm
Forum: SIMATIC system
Topic: daylight saving detection
Replies: 4
Views: 3397

Re: daylight saving detection

Hi, For DCF77 You need hardware. There is some functions in OSCAT library link: http://www.oscat.de/component/jdownloads/category/2-oscat-basic.html?Itemid=0 there You can find oscat_basic_332_s7 Step7 library with various functions. In manual oscat_basic333_en there is one function DT2_TO_SDT which...
by dsekulic
Sat Dec 27, 2014 10:25 pm
Forum: SIMATIC system
Topic: Question about PN data reading
Replies: 6
Views: 3915

Re: Question about PN data reading

Hi,
I see that Your PLCs are in different subnets. Did You try to establish connection when PLCs are in same subnet. It is possible that Your router block some traffic. Are Your PLCs in same Step7 project? Maybe You should send me project to take a short look.
regards
by dsekulic
Fri Dec 19, 2014 3:14 am
Forum: Simatic (Russian)
Topic: Нормально открытый контакт не реагирует на команды 0 и 1
Replies: 8
Views: 6192

Re: Нормально открытый контакт не реагирует на команды 0 и 1

Hi,
You should not be able to change digital input as You described. Everything is OK with Your installation. It is possible to change for example local memory bits (M0.0...), or some instance or shared data block bits (DI or DB).
regards
by dsekulic
Thu Dec 18, 2014 7:21 am
Forum: Simatic (Russian)
Topic: Нормально открытый контакт не реагирует на команды 0 и 1
Replies: 8
Views: 6192

Re: Нормально открытый контакт не реагирует на команды 0 и 1

Hi,
If You force digital input in one scan than in another scan it is overwritten by real value in process image. If You use PLCSIM then You should force DI in PLCSIM itself. In case of real PLC You should force DI on DI module.
regards
by dsekulic
Wed Dec 03, 2014 1:49 pm
Forum: SIMATIC system
Topic: Communication between PLC S7 414 and PLC S7 417
Replies: 2
Views: 2280

Re: Communication between PLC S7 414 and PLC S7 417

Hi, You should use following manual https://support.automation.siemens.com/WW/adsearch/resultset.aspx?region=WW&lang=en&netmode=internet&ui=NDAwMDAxNwAA&term=communication+manual+simatic&ID=78028908&ehbid=78028908&docid=80635207 Go to JUMP DISTRIBUTOR on page 73. Your case is described in 21.5.3 (pa...
by dsekulic
Tue Dec 02, 2014 2:15 pm
Forum: SIMATIC system
Topic: Question about PN data reading
Replies: 6
Views: 3915

Re: Question about PN data reading

Hi, You should use following manual https://support.automation.siemens.com/WW/adsearch/resultset.aspx?region=WW&lang=en&netmode=internet&ui=NDAwMDAxNwAA&term=communication+manual+simatic&ID=78028908&ehbid=78028908&docid=80635207 Go to JUMP DISTRIBUTOR on page 73. Your case is described in 21.4.2 (pa...
by dsekulic
Thu Jul 10, 2014 5:16 pm
Forum: Utilites for Simatic PLC
Topic: [?]: PLC S7-1200 Tool connected over ethernet
Replies: 3
Views: 8051

Re: [?]: PLC S7-1200 Tool connected over ethernet

Hi,
I think that S7-1200 tool is extracted from TIA portal. You should choose right interface for connection to S7-1200.

http://support.automation.siemens.com/W ... n/41737437

regards
by dsekulic
Wed Jul 09, 2014 10:48 am
Forum: Utilites for Simatic PLC
Topic: [?]: PLC S7-1200 Tool connected over ethernet
Replies: 3
Views: 8051

Re: [?]: PLC S7-1200 Tool connected over ethernet

Hi,
I connect without any problems to S/-1200 over 64bit Win7 with TIA portal V12. You should choose right PG/PC interface in Online & diagnostics tool in TIA portal.
regards
by dsekulic
Sun Apr 27, 2014 8:13 am
Forum: SIMATIC system
Topic: [?] Combine two Words
Replies: 5
Views: 4616

Re: [?] Combine two Words

Hi, If You read question he need to get result 16#BD0744 not 16#BD070044. Therefore I combine second word as byte. If You put in STL L 16#44 You will get L B#16#44 That is just answer on question. If You wish to combine 16#BD07 and 16#0044 then You should shift left 16 bits L W#16#BD07 SLD 16 // shi...
by dsekulic
Thu Apr 24, 2014 8:45 am
Forum: SIMATIC system
Topic: [?] Combine two Words
Replies: 5
Views: 4616

Re: [?] Combine two Words

Hi,
One correction
Instead of SLD 4 You should put SLD 8 because You need to insert one byte.
regards
by dsekulic
Wed Apr 23, 2014 9:39 pm
Forum: SIMATIC system
Topic: [?] Combine two Words
Replies: 5
Views: 4616

Re: [?] Combine two Words

Hi,
You should do following

stl:

L W#16#BD07
SLD 4 // shift left double word
L B#16#44
OD // bitwise OR double word
T MD 0 // result

regards
by dsekulic
Thu Nov 21, 2013 8:12 am
Forum: Siemens Hardware & Software
Topic: [?]: S7 Siemens SPS SIMATIC Manager
Replies: 1
Views: 4507

Re: [?]: S7 Siemens SPS SIMATIC Manager

Hi,
You should use PLCSIM.
Take a look here
viewtopic.php?p=47220#p47220
regards
by dsekulic
Sat Nov 02, 2013 7:14 am
Forum: Other (only about CAD and Soft)
Topic: [LINK]: EPLAN Electric P8 Reference Handbook 3ed
Replies: 14
Views: 19338

Re: [LINK]: EPLAN Electric P8 Reference Handbook 3ed

Hi,
It seams that link is good. I try it right now and everything working fine.
regards
by dsekulic
Thu Oct 10, 2013 6:18 pm
Forum: SIMATIC system
Topic: [HELP] Connecting CP-341 as master [MODBUS RTU]
Replies: 2
Views: 2696

Re: [HELP] Connecting CP-341 as master [MODBUS RTU]

Hi, You need to install Loadable driver CP PtP Modbus Master ( https://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&lang=en&siteid=cseus&aktprim=0&extranet=standard&viewreg=WW&objid=24284824&treeLang=en ). Also You need Modbus master hardware dongle 6ES7870-1AA01-0YA0 which is plu...
by dsekulic
Sun Sep 22, 2013 9:46 am
Forum: SIMATIC system
Topic: Ethernet in communication profilbus
Replies: 1
Views: 1832

Re: Ethernet in communication profilbus

Hi, If You want to use ET200 on Profibus it depend on which type of ET200 You will use. You have ET200S, ET200M, ET200SP for installation in control cabinet or ET200eco and ET200pro for installing outside of control cabinet. You will need Interface module for Profibus for each extension and I/O modu...
by dsekulic
Mon Sep 09, 2013 3:50 pm
Forum: Other (only about CAD and Soft)
Topic: [?]: EPLAN Fluid 2.2 - symbol library is empty.
Replies: 1
Views: 4026

Re: [?]: EPLAN Fluid 2.2 - symbol library is empty.

Hi,
You should define libraries which You want to use in each project. Open project You want to edit. Go on Option->Settings...->Projects->"Project name"->Managemet->Symbol libraries. You can specify desired libraries there by pressing Symbol libraries filed.
regards
by dsekulic
Wed Sep 04, 2013 5:22 pm
Forum: SIMATIC system
Topic: [?]: How to lock or unlock FB bloks?
Replies: 5
Views: 7806

Re: [?]: How to lock or unlock FB bloks?

Hi,
Take a search on this site s7canopener. With this tool You can unprotect / protect S7 blocks.
regards
by dsekulic
Mon Jul 15, 2013 4:05 pm
Forum: SIMATIC system
Topic: [?]: PID Temperature Control
Replies: 1
Views: 2300

Re: [?]: PID Temperature Control

Hi, take a look on https://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csSearch&objaction=cssearch&lang=en&siteid=cseus&query=&query2=pid%20temperature%20control&content=adsearch%2Fadsearch.aspx This is a manual for PID temperature control. Probably You need step controller FB59 (TCONT_...
by dsekulic
Mon Apr 08, 2013 11:43 pm
Forum: Other (only about CAD and Soft)
Topic: [?+]: change switch position text in Eplan P8
Replies: 4
Views: 4093

Re: change switch position text in Eplan P8

Hi, Open new symbol which You intend to modify (Utilities->Master Data->Symbol->Open). In symbol editor select some symbol properties (for example Device Tag). Right click->Properties. Afterward select icon new (Ctrl+Alt+N). From the list choose property which is interesting for You (for ex. User Su...
by dsekulic
Mon Apr 08, 2013 3:00 am
Forum: Other (only about CAD and Soft)
Topic: [?+]: change switch position text in Eplan P8
Replies: 4
Views: 4093

Re: change switch position text in Eplan P8

Hi, You have several options. First is to change original symbol which You insert in scheme. Go to Utilities->Master Data->Symbol->Open. Open symbol which You already insert. There You can change look of mentioned symbol. Second option is to make copy of symbol You want to modify. Go to Utilities->M...
by dsekulic
Fri Mar 01, 2013 10:00 pm
Forum: SIMATIC system
Topic: Monitor profibus ladder on a network
Replies: 4
Views: 2785

Re: Monitor profibus ladder on a network

Hi,
You need Profibus connector with PG interface on top. Also You need communication processor CP5711 or genuine Siemens PG.
regards
by dsekulic
Tue Jan 29, 2013 3:19 pm
Forum: Utilites for Simatic PLC
Topic: [?]: S7 HVAC LIBRARY
Replies: 1
Views: 6022

Re: [?]: S7 HVAC LIBRARY

Hi,
Did You try on http://www.oscat.de. There You have S7 library for building automation alongside with explanations. This is open source code and free to download.
regards
by dsekulic
Mon Sep 17, 2012 3:19 pm
Forum: SIMATIC HMI
Topic: Request: wincc opc server for knx
Replies: 2
Views: 4451

Re: wincc opc server for knx

Hi,
There is one more very good OPC for KNX (http://www.netxautomation.com) but problem with netx is that they require hardware dongle.
regards
by dsekulic
Sat Sep 01, 2012 8:51 am
Forum: Other (only about CAD and Soft)
Topic: [?]: EPLAN P8 - creating a new symbol unsuccessful
Replies: 3
Views: 5151

Re: [?]: EPLAN P8 - creating a new symbol unsuccessful

Hi,
Maybe You should reinstall eplan or if You have some backup of Your symbol library.
regards
by dsekulic
Fri Aug 31, 2012 1:29 pm
Forum: Other (only about CAD and Soft)
Topic: [?]: EPLAN P8 - creating a new symbol unsuccessful
Replies: 3
Views: 5151

Re: [?]: EPLAN P8 - creating a new symbol unsuccessful

Hi, I think that the better idea is first to copy symbol which You want to change (Utilities -> Master Data -> Symbol -> Copy). Then such copied symbol adapt to Your need (delete pins and adapt Function definition - now transducer with two pins). You probably made changes to original symbol (transdu...
by dsekulic
Wed Aug 15, 2012 11:52 pm
Forum: Other (only about CAD and Soft)
Topic: Eplan4 Z13 files
Replies: 3
Views: 8952

Re: Eplan4 Z13 files

Hi,
If You use Eplan P8 than You can use import Eplan5 project. Go to Project->Eplan5/fluidPlan data import->Project...
Press on Surce dots and in popup check Data Backup (z13,...). Afterward You select Your z13 file
regards
by dsekulic
Wed Jul 18, 2012 1:19 am
Forum: SIMATIC system
Topic: Need advice about DP-Slaves diagnosis
Replies: 3
Views: 3915

Re: Need advice about DP-Slaves diagnosis

Hi,
You can use Report System Error. In Hardware configuration when You select CPU under Options You can find report system error. Another possibilities is to use SFC51 (read system status list)
kind regards
by dsekulic
Sun Jun 03, 2012 9:48 am
Forum: SIMATIC system
Topic: [?]: temporisation with step7
Replies: 5
Views: 5243

Re: [?]: temporisation with step7

Hi,
Maybe You should look for SFC101 (Handling Runtime Meters), alongside with SFC2 (SET_RTM), SFC3 (CTRL_RTM) and SFC4 (READ_RTM).
Description of this functions You will find in System Software for S7-300/400
System and Standard Functions
.
regards
by dsekulic
Wed Feb 29, 2012 7:31 am
Forum: Other (only about CAD and Soft)
Topic: [EPLAN] Multi-line to single-line shematics ??
Replies: 4
Views: 5810

Re: [EPLAN] Multi-line to single-line shematics ??

Hi, You have option Utilities->Exchange symbols single-line<-->multi-line. You select part of elements/pages to convert to single line and apply exchange symbol. But first You have to include IEC single symbol library in Your project (Option -> Setting...-> Projects -> Your project name -> Managemen...
by dsekulic
Fri Jan 20, 2012 8:32 pm
Forum: SIMATIC system
Topic: [?]: Simatic STEP7 PID Controller example ?
Replies: 5
Views: 10324

Re: [?]: Simatic STEP7 PID Controller example ?

Hi,
Maybe You should start from here
https://www.automation.siemens.com/WW/f ... age=en#top
Here You will find program example for FB41. Also You should call FB41 in some cyclical interrupt OB (for example OB35).
regards